The macros listed in Table 3.2.20- 3.2.23 can be used to return real face variables in SI units. They are identified by the F_ prefix. Note that these variables are available only in the pressure-based solver. In addition, quantities that are returned are available only if the corresponding physical model is active. For example, species mass fraction is available only if species transport has been enabled in the Species Model dialog box in ANSYS FLUENT. Definitions for these macros can be found in the referenced header files (e.g., mem.h).

The macro listed in Table 3.2.20 can be used to obtain the real centroid of a face. F_CENTROID finds the coordinate position of the centroid of the face f and stores the coordinates in the x array. Note that the x array is always one-dimensional, but it can be x[2] or x[3] depending on whether you are using the 2D or 3D solver.

**Table 3.2.20:** Macro for Face Centroids Defined in `metric.h`
Macro	Argument Types	Outputs
`F_CENTROID(x,f,t)`	`real x[ND_ND]`, `face_t f`, `Thread *t`	`x` (face centroid)

The ND_ND macro returns 2 or 3 in 2D and 3D cases, respectively, as defined in Section 3.4.2. Section 2.3.15 contains an example of F_CENTROID usage.

F_AREA can be used to return the real face area vector (or `face area normal') of a given face f in a face thread t. See Section 2.7.3 for an example UDF that utilizes F_AREA.

**Table 3.2.21:** Macro for Face Area Vector Defined in `metric.h`
Macro	Argument Types	Outputs
`F_AREA(A,f,t)`	`A[ND_ND]`, `face_t f`, `Thread *t`	`A` (area vector)

By convention in ANSYS FLUENT, boundary face area normals always point out of the domain. ANSYS FLUENT determines the direction of the face area normals for interior faces by applying the right hand rule to the nodes on a face, in order of increasing node number. This is shown in Figure 3.2.1.

ANSYS FLUENT assigns adjacent cells to an interior face ( c0 and c1) according to the following convention: the cell out of which a face area normal is pointing is designated as cell C0, while the cell in to which a face area normal is pointing is cell c1 (Figure 3.2.1). In other words, face area normals always point from cell c0 to cell c1.

Download Шєшµщ€щљш± Щ…щ† Щѓщ€щ‚ Ш§щ„шішш§шё Щ„шјш±щ€ш№ Шєщ„ш§щ€ш© Шєщ‡шїш¦ Ш§щ„шјш№шµш§шё Щ€ш§щ„щ†щѓщ€ші Щѓщљ Ш§щ„ш№ш§щ„щ… Ш§щ„шґщљш® Ш№шёшї Ш§щ„шёш§шіш· Ш№шёшї Ш§щ„шµщ…шї Hd(m4a 128k) M4a -

Here is a short story about the peace this specific recording can bring: The Calm Above the Storm

As the camera glided over the silent, cloud-filled horizon, Omar’s heartbeat began to slow. He closed his eyes. In his mind, he wasn't sitting in a cramped apartment anymore; he was drifting through that endless blue sky. The "HD" quality of the sound made it feel like the Sheikh was standing right there in the room, reciting just for him. Here is a short story about the peace

It wasn't just a voice; it was a force of nature. The Sheikh’s legendary breath control and melodic tone turned every word into a vibration that resonated deep in Omar’s chest. The recitation was slow, steady, and incredibly clear. and incredibly clear.

The macros listed in Table 3.2.23 access flow variables at interior faces and boundary faces.

**Table 3.2.23:** Macros for Interior and Boundary Face Flow Variables Defined in `mem.h`
Macro	Argument Types	Returns
`F_P(f,t)`	`face_t f`, `Thread *t`,	pressure
`F_FLUX(f,t)`	`face_t f`, `Thread *t`	mass flow rate through a face

F_FLUX can be used to return the real scalar mass flow rate through a given face f in a face thread t. The sign of F_FLUX that is computed by the ANSYS FLUENT solver is positive if the flow direction is the same as the face area normal direction (as determined by F_AREA - see Section 3.2.4), and is negative if the flow direction and the face area normal directions are opposite. In other words, the flux is positive if the flow is out of the domain, and is negative if the flow is in to the domain.

Note that the sign of the flux that is computed by the solver is opposite to that which is reported in the ANSYS FLUENT GUI (e.g., the Flux Reports dialog box).

3.2.4 Face Macros